Electric Vehicle Parts
JUST FOR FUN… GAS DRIVE COMPONENTS... vs. ELECTRIC DRIVE COMPONENTS !!!!
NEED A CUSTOM KIT?
E-mail us for pricing, invoicing, additional packages, shipping. We are HAPPY to accommodate your needs and your budget.
AC Propulsion 150 COMPLETE
Motor, Controller, Charger, BSM, Prelude Transmission
NOW $7,000 or BEST OFFER
( over $25,000 retail)…
This won’t last long !!
PERFECT for your next RACE CAR !!!!
The new NetGain HyPer9 AC Motor X1 Controller Kit 120 Volt [H9-ACX1]
The long awaited AC motor from NetGain is here. The new 9 inch HyPer9 AC motor is based on a new high efficiency design. The motor is a permanent magnet assisted synchronous reluctance design and holds the highest efficiency rating of IE3 at 94% motor efficiency. The motor is IP67 sealed. The matching controller, an AC-X1 by SME Group will accept a supply side DC voltage of up to 132 Volts, and will output up to 760 Amps output, with a peak 88kW of power. The permanent magnets are a new design that are manufactured without the use of rare earth elements, but still gain a big efficiency advantage with a powerful 173 lb/ft of torque. See FULL description and pictures below. ACCEPTING PRE ORDERS FOR NOVEMBER DELIVERY.
This kit includes:
HyPer 9 Motor
SME AC-X1 Controller
35 Pin Connector and Wire Harness
Gigavac GV200-QA Contactor
12 Volt HV Relay
SME Dash Gauge w/ Speed
Motor Face: B-Face (Warp Compatible)
Motor Diameter: 9.0 Inches
Motor Case Length: 13.75 Inches
Motor Shaft Length: 2.0 Inches
Motor Shaft to End Length: 15.75 Inches
Motor Type: Permanent Magnet Synchronous Reluctance AC
Weight: 90 lbs
Max Voltage Input: 132
Terminal Stud Size: M8 Inch
Integrated Sensors: Encoder and Temperature
Rated Torque: 173 Lb Ft
Rated Power: 120 HP
Max RPM: 8,000
RPM Sensor: Yes
Drive End Shaft: 1-1/8 Inch with 1/4 Inch Keyway
Accessory End Shaft: Not Available (coming soon)
Max Efficiency: 0.94
Thermal Cooling: External Heatsink
Max Temperature: 150 Degrees Celsius
Matching Controller Included In Price:
Note: Due to the excessive weight of motors additional freight charges apply.
Warranty Period: 2 Years
YES we have the new (2016) TransWarp 9!
- Designed for dual motor and direct drive applications! $2,800.00
- 32-tooth, hardened and splined DE shaft
- Extra strength DE bearings
- Field adjustable timing
- Terminal Jumper included
- 4 mounting holes on CE for adding appliances or coupling to an ImPulse 9™
- 1.125” diameter, keyed CE shaft matches Imulse 9™ DE
- Mounts directly to a Turbo 400, “shorty” tail-shaft housing for easy mounting
- Optional 1350 slip-yoke assembly
Our MOST POPULAR DC ELECTRIC MOTORS:
Net Gain WarP 11″ Motor
Max Diameter – 11.45, Length 21.84, Weight 233 Lbs. – 74.3 Torque 1000A
Net Gain WarP 9″ Motor
Max Diameter – 9.25, Leng,th 20.19, Weight 143 Lbs. – 59.3 Torque 1000A
All Motors have a 1/2″ – 20 hole in the DE end-bell for the addition of a RPM Sensor. All Motors produced with 1.125″ CE Shaft.
Other sizes available, email for quote.
SUGGESTED DIY APPLICATION UNDER $6,000
Our Most Popular Package $5,892
Does NOT INCLUDE SHIPPING or Batteries
Warp 9″ Motor: $2,250.00
750Amp/144V Controller $1,200.00
Emergency Disconnect: $45.00
Accelerator, PB-6: $115.00
500 Amp Fuse $ 89.00
DC to DC Converter: $179.00
Adapter Plate, ( for most, if available) $925.00
EMAIL FOR INVOICING:
Provide Battery pack voltage at the time of placing order, 120V, 144V, 156V.
* Recommended/ 0ptional.
** Recommended, or BMS
If you want a CUSTOM KIT. . . E-mail us for pricing, invoicing, additional packages, shipping. We are HAPPY to accommodate your needs and your budget.
ALA CARTE ELECTRIC PARTS
Z1K-LV (72-156V : $2,175.00
Z1K-HV (72-300) : $2,675.00
Z2K-LV (72-156V) $3,975.00
Z2K-HV (72-300V) $4,525.00
Z2K-EHV (72-348V) $5,075.00
HAIRBALL: Starting at $275.00
Other Options for Hairballs available- Email for pricing
We also carry ALTRAX Controllers for your smaller projects.
( BOATS… LAWN MOWERS….Scooters, Motorcycles………)
Email for pricing
$825.00 up to $1,250.00
SB350 – 1/0 $15.99
SB350 – 2/0 $25.99
Vacuum Pumps - Call for pricing
DC to DC CONVERTER
600W with PFC and Parallel Function
Output: 13.5 Volts @ 44.5 Amps
- Universal AC input / Full range
- Built-in active PFC function
- Protections: Short circuit / Overload / Over voltage / Over temperature
- Forced air cooling by built-in DC fan
- With DC OK Signal output
- Current sharing up to 2400W(3+1)
- Built-in remote ON-OFF control
- Built-in remote sense function
- Fixed switching frequency at PFC:88KHz PWM:100KHz
Intelligent Ampere Hour Meter
Displays Volts, Amps, Amp hours, and time. Used to monitor state of charge of LiFePo4 cells. This device features two control relays with NO and NC connections that can be activated by Voltage, Current, or Accumulated Ampere Hours. These relays can be used to disable controller, disconnect chargers, etc.
Includes Meter, 500amp shunt
- Dual Alarm output (relay) J1,J2
- Voltage range: 500 and 100v
- Max current: 9999A (an external shunt required)
- Amp-Hr recording: 0.001~9999AH
- Sampling: 3/s
- Control Type: Relays
- Relay: 3A@125VAC, 3A@14V DC
- Display: Blue LED ( RED also available)
- Size: 96mm x48mm x62mm Mount Hole: 92mm x44mm x62mm
ADD BUCK Enhanced – $300.00
The new model X series comes standard with a Multifunction meter showing the input Amps, Volts, KiloWatts and Power Factor. Fully assembled and tested with full reg bus interface.
20 amps in to 20 amps out
Buck Enhanced model:
20 amps in to 30 amps out
The PFC20 weighs 16 pounds and resides in a box that is 13 x 9 x 5.5 inches
The new model X series comes standard with a Multifunction meter showing the input Amps, Volts, KiloWatts and Power Factor. Fully assembled and tested with full reg bus interface. Now available with digital voltage selection.
Capable of 30 amps in & 40 amps out.
The PFC30 weighs 17.2 pounds and resides in a box that is 13 x 9 x 5.5 inches.
Other Chargers also available, email for info and prices.
- Internal integrated PFC, no pollution to electric network, minimizes disturbance on electric network from heavy current.
- Wide input voltage range AC85V~AC265V available for worldwide requirements, convenient for electric-network fluctuation and vehicles exportation.
- High efficiency, above 93%, while traditional chargers can meet only about 80% efficiency.
- Intelligent temperature compensation function in the charging process, preventing damage to the battery caused by charge-off or charge due, greatly extending the lifespan of the battery.
- Fully-sealed and water-proof, protection class IP46. Shock resistance treatment made inside makes vibration-proof level up to SAEJ1378 that can fully meet the standard of automobile appliance usage.
- Available for various kind of batteries like Lead-Acid, LiFePO4 etc., Flexible and programmable charging module. Ability to select 10 different Amp Hour or Cell Count settings. Equipped with CAN communication interface to realize real-time communication with BMS.
Lithiums: Calbs $1.45 ah
( Plus Shipping)
48 – 100 ah Cells: 40 to 60 mile range: 15kw pack
60 – 200ah Cells 100 to 150 mile range: 38.4kw pack
60 – 300ah cells 140 to 225 mile range: 57.6kw pack
CALB BATTERIES and LEAF CELLS, when available VOLT CELLS
ALL PRICES, SHIPPING, TAXES SUBJECT TO CHANGE WITHOUT WARNING . . . WE CAN ALSO OFFER VOLT AND LEAF CELLS, WHEN AVAILABLE. ASK US WHAT WE HAVE.
AC systems - INCLUDES:
Motor, Controller, Generic Harness, Display and Contactor.
Call for Pricing on other systems:
Our most Popular is: ( Call for up to date prices).
AC-35 – 72V $3,850.00 plus shipping
AC-35 – 96V $4,150.00 plus shipping
AC-35 – 144V $4,900.00 plus shipping
We are proud to carry the new MasterFlux AC System …
We are offering the SIERRA Compressor with SAE #8 and #10 fittings; Digital Controller 120-420V DC, Wiring Harness: Compressor to Controller, Mounting Kit and a 600V, 50A Diode. ALL you need to have great AC in your EV.
All for $1,999.00 INCLUDING SHIPPING to most states. (extra for international shipping)
Kit DOES NOT include hoses. You will have to take your existing hoses to someone for the new ends to be put on. Our experience was less than $80.00. And if you take your Vehicle to an AC Shop to have the R134a (NO OIL) put in… use the specs for your vehicle. Our experience was 1.1lbs for a cost of about $60.